- The Soft Contact bits are anatomically shaped This double jointed loose ring snaffle is made of solid Cuprigan with stainless steel rings. Cuprigan is an alloy consisting of 89% copper, 7% aluminium, 3% iron and 1% zinc. The oxidation process of the material gives a pleasant smell and taste. The anatomical design of the bit follows the shape of the horse’s mouth, which allows for a gentle and even pressure distribution. The slightly curved shape of the mouthpiece ensures a little bit more space for the sides of the tongue. The design, combined with the unique properties of Cuprigan, encourages the chewing process and saliva production, which allows for a pleasant connection with the sensitive horse’s mouth. The bit applies mild pressure on the mouth. Mouthpiece thickness 12 mm, ring size 50 mm. A loose ring snaffle allows the mouthpiece to move freely relative to the rings. The bradoon is usually used in combination with a Weymouth Curb bit. The small rings leave more space for the Weymouth Curb than regular loose ring snaffles. The bradoon should ideally be 0,5-1 centimeter larger than the Weymouth Curb.
- This high quality double jointed three ring gag is made of solid Cuprigan with stainless steel rings. Cuprigan is an alloy composed of 89% copper, 7% aluminum, 3% iron and 1% zinc. The oxidation process of the material gives it a pleasant smell and taste. The anatomical design of the bit follows the shape of the horse's mouth, allowing for smooth, even pressure distribution. The design, combined with the unique properties of Cuprigan, stimulates the chewing process and saliva production, allowing for a pleasant connection with the horse's sensitive mouth. The bit applies normal pressure to the mouth and is suitable for hard-mouthed horses. Nozzle thickness 16mm, center ring size 70mm. The three-ring gag has two additional rings: one on the top and one on the bottom. The upper ring is attached to the cheek pieces of the bridle, the reins can be attached to either of the two lower rings. The less the reins are tightened, the stronger the influence on the polls will be. The bit can be used with one or two reins or with Pelham rounds attached to the middle and lower ring. The double joint drill bit consists of three parts. The center section of the mouthpiece lies flat on the tongue, causing more pressure on the tongue than a single hinged bit. The thicker the midsection, the more pressure it will create on the tongue.
- Ring diameter: 6.5 cm. Caliber: 14mm. The SENSOGAN material results from an optimal combination of Copper, Manganese and Zinc. The combination of Manganese with a low copper content makes this material much softer and with a much more reduced and compensated oxidation process. Manganese is an important micronutrient for the development of metabolism and the reduction of stress. The low copper content reduces the appearance of stains. * Toxicologically tested. * High tolerance. * Easy to clean. * Facilitates the constant flow of saliva. In the Sprenger catalogue, quality codes 78 (golden mouthpiece with stainless rings), and 79 (golden mouthpiece and rings). Dynamic RS * Ergonomic shape. * No pressure on the palate. The pressure is distributed throughout the mouth. * Gentle on the mouth and tongue. * The embouchure joint is twisted up to 45 degrees. * Curved joints keep the snaffle in the correct position in the center of the mouth.
- Sweet Iron tips are known for the sweet taste of the mouthpiece. Additionally, the tips are anatomically shaped and available in many shapes and sizes. This Double Joint Dee-Ring Bit is made of solid stainless steel rings and a mild steel collet combined with a layer of soft iron on the collet (blue). Sweet iron stimulates the chewing process and saliva formation. When this material reacts with moisture, heat and air in a process called oxidation, the surface rust has a sweet taste. As a result, the horse will be more willing to accept the bit. The blue color disappears over time, but the taste of surface rust remains. The anatomical design of the bit follows the shape of the horse's mouth, allowing for smooth, even pressure distribution. The double joint drill bit consists of three parts. The center section of the mouthpiece sits flat on the reed, which puts more pressure on the reed than a single hinged tip would. The thicker the middle section, the more pressure it will create on the tongue. Nozzle thickness 14mm, ring size 65mm. The Dee-ring bit has fixed cheek pieces, so the aids will have a more direct effect. This type of bit is often easily accepted as it offers stability. The shape of the bit prevents pulling through the mouth and provides a lateral guiding effect, making them an excellent choice for young horses.